The JBL Pulse is a well-liked Bluetooth speaker due to its portability, sound high quality, and built-in mild present. Nonetheless, if you could restore your Pulse or exchange a element, you will must know tips on how to disassemble it. Happily, the method is comparatively easy and might be accomplished in only a few minutes with the precise instruments.
To start out, you will want to assemble a couple of instruments. You may want a Phillips head screwdriver, a flathead screwdriver, and a spudger. You might also need to put on gloves to guard your fingers from any sharp edges. Upon getting your instruments, you possibly can start the disassembly course of.
First, take away the 4 Phillips head screws on the underside of the speaker. Then, use the flathead screwdriver to pry off the underside panel of the speaker. As soon as the underside panel is eliminated, you will see the battery, the circuit board, and the speaker drivers. To take away the battery, merely disconnect the battery connector and raise the battery out of the speaker. To take away the circuit board, disconnect the entire connectors and unscrew the 2 Phillips head screws that maintain the circuit board in place. To take away the speaker drivers, merely unscrew the 4 Phillips head screws that maintain every driver in place.
Find out how to Disassemble a JBL Pulse
Disassembling a JBL Pulse is a comparatively simple course of that may be accomplished in about half-hour. The next steps will information you thru the method:
1.
Energy down the JBL Pulse and disconnect it from any energy sources.
2.
Take away the 4 screws on the underside of the JBL Pulse. These screws are positioned in every nook of the gadget.
3.
Gently pry open the again cowl of the JBL Pulse. The again cowl is held in place by a collection of clips. Watch out to not injury the clips.
4.
Find the battery and disconnect it from the motherboard. The battery is positioned within the middle of the gadget. It’s held in place by a single screw.
5.
Take away the 4 screws that safe the motherboard to the chassis. The motherboard is positioned within the prime of the gadget.
6.
Gently raise the motherboard out of the chassis. Watch out to not injury the ribbon cables that join the motherboard to the opposite elements.
7.
Disconnect the ribbon cables that join the motherboard to the opposite elements. The ribbon cables are positioned on the perimeters of the motherboard.
8.
Take away the remaining elements from the chassis. The remaining elements embody the speaker, the LEDs, and the buttons.
Upon getting disassembled the JBL Pulse, you possibly can start to restore or exchange the broken elements.
Folks Additionally Ask
How do I repair a JBL Pulse that will not activate?
There are some things that would trigger a JBL Pulse to not activate. First, be sure that the battery is charged. If the battery is just not charged, strive charging it for no less than half-hour. If the battery is charged, however the JBL Pulse nonetheless will not activate, strive resetting the gadget. To reset the gadget, press and maintain the facility button for 10 seconds. If the JBL Pulse nonetheless will not activate, you might must contact customer support.
How do I exchange the battery in a JBL Pulse?
To exchange the battery in a JBL Pulse, you have to to disassemble the gadget. Upon getting disassembled the gadget, you have to to find the battery. The battery is positioned within the middle of the gadget. It’s held in place by a single screw. Upon getting positioned the battery, disconnect it from the motherboard and take away it from the gadget. To put in the brand new battery, merely reverse the steps.
How do I restore the LEDs in a JBL Pulse?
To restore the LEDs in a JBL Pulse, you have to to disassemble the gadget. Upon getting disassembled the gadget, you have to to find the LEDs. The LEDs are positioned on the perimeters of the motherboard. Upon getting positioned the LEDs, you have to to check them to see which of them will not be working. To check the LEDs, you have to a multimeter. Upon getting recognized the defective LEDs, you have to to switch them. To exchange the LEDs, you have to to desolder the previous LEDs and solder within the new LEDs.
