Uninstalling a Ring Doorbell is an easy course of that may be accomplished in a couple of minutes. Nevertheless, there are some things you must take into accout earlier than you start. First, just be sure you have the required instruments. You will want a screwdriver, a drill, and a pair of pliers. Second, you’ll want to disconnect the facility to the doorbell earlier than you start engaged on it. Lastly, take your time and comply with the directions rigorously. If you’re not comfy engaged on electrical tools, it’s best to rent a professional electrician.
After you have gathered your instruments and disconnected the facility, you may start the removing course of. First, take away the 2 screws which can be situated on the underside of the doorbell. Subsequent, use a drill to take away the 2 screws which can be situated on the highest of the doorbell. As soon as the screws have been eliminated, you may rigorously pull the doorbell away from the wall. You’ll want to help the doorbell with one hand when you are eradicating the screws. Lastly, disconnect the wires which can be related to the doorbell. As soon as the wires have been disconnected, you may take away the doorbell from the wall.
Disconnecting the Ring Doorbell System
Earlier than eradicating your Ring Doorbell, it is important to disconnect it correctly to stop harm or knowledge loss. Comply with these steps to soundly disconnect your Ring Doorbell:
-
Energy Down the Doorbell: Find the small black button on the again of your Ring Doorbell. Press and maintain this button for 10 seconds till the sunshine on the entrance of the doorbell turns off. This motion will energy down the doorbell and disconnect it from the facility supply.
-
Take away the Faceplate: As soon as the doorbell is powered down, gently pull the faceplate straight towards you. The faceplate ought to come off simply, revealing the mounting screws beneath.
-
Unscrew the Mounting Screws: Utilizing a screwdriver, rigorously unscrew the 2 mounting screws situated on the backside of the doorbell. Be certain that to carry the doorbell regular as you unscrew the screws to stop it from falling.
-
Disconnect the Wires: In case your Ring Doorbell is wired, there will probably be two wires related to the again of the system. Gently pull the wires straight out of the doorbell to disconnect them. If the wires are related with wire nuts, unscrew the wire nuts and separate the wires.
-
Take away the Doorbell: As soon as the wires are disconnected, rigorously raise the Ring Doorbell off the mounting bracket. You’ll want to help the doorbell as you raise it to stop it from dropping and inflicting harm.
Eradicating the Faceplate
To take away the faceplate, start by greedy the underside fringe of the doorbell and pulling it straight in the direction of you. There will probably be some resistance, so use a agency grip and keep away from pulling too laborious. When you encounter any issue, attempt wiggling the doorbell forwards and backwards whereas pulling to loosen it.
As soon as the underside edge is launched, proceed pulling upwards to take away the remainder of the faceplate. Watch out to not contact the wires or terminals behind the faceplate, as this might trigger harm or damage.
As soon as the faceplate is totally eliminated, you’ll have entry to the mounting bracket and wiring terminals. From right here, you may proceed with disconnecting the wires, eradicating the mounting bracket, and finishing the removing course of.
Ideas for Eradicating the Faceplate
- Make sure that the doorbell is powered off earlier than making an attempt to take away the faceplate.
- Use a agency grip and pull straight in the direction of you to keep away from damaging the system.
- When you encounter resistance, attempt wiggling the doorbell forwards and backwards whereas pulling to loosen it.
- Keep away from touching the wires or terminals behind the faceplate, as this might trigger harm or damage.
Disconnecting the Wires
Earlier than you take away your Ring Doorbell, you will have to disconnect the wires. Here is do it:
- Flip off the facility to your doorbell on the breaker field.
- Take away the faceplate of your doorbell.
- Find the 2 wires related to the terminals on the again of your doorbell.
- Use a screwdriver to loosen the screws that maintain the wires in place.
- Gently pull the wires away from the terminals.
- Cap the ends of the wires with electrical tape.
Here is a desk summarizing the steps:
| Step | Motion |
|---|---|
| 1 | Flip off the facility to your doorbell on the breaker field. |
| 2 | Take away the faceplate of your doorbell. |
| 3 | Find the 2 wires related to the terminals on the again of your doorbell. |
| 4 | Use a screwdriver to loosen the screws that maintain the wires in place. Gently pull the wires away from the terminals. Cap the ends of the wires with electrical tape. |
Cleansing the Floor and Mount
To take care of the optimum functioning of your Ring Doorbell, common cleansing is important. Here is a step-by-step information to maintaining your system in pristine situation:
Instruments you will want:
- Tender microfiber material
- Heat water
- Isopropyl alcohol (elective, for cussed stains)
Step 1: Wipe Down the Floor
Gently wipe the floor of your Ring Doorbell with a comfortable microfiber material dampened with heat water. This may take away any mud or grime that has gathered.
Step 2: Clear the Mount
Take away the Ring Doorbell from the mount by turning it counterclockwise and lifting it straight up. Wipe down the mount with a comfortable microfiber material dipped in heat water to take away any grime or particles.
Step 3: Handle Cussed Stains (Optionally available)
When you encounter cussed stains, dampen a comfortable microfiber material with isopropyl alcohol and gently rub the affected space in round motions. Keep away from utilizing harsh chemical substances or abrasive cleaners, as they will harm the system’s floor.
Step 4: Reattach the Doorbell
As soon as the mount is clear, reattach the Ring Doorbell by aligning it with the mount and turning it clockwise till it locks into place.
Step 5: Rinse and Dry
When you used isopropyl alcohol to take away stains, rinse the floor of the Ring Doorbell with a clear, damp microfiber material to take away any residue. Permit the system to air dry fully earlier than placing it again into service.
Extra Ideas
Listed here are some further suggestions to remember:
- Clear your Ring Doorbell recurrently to stop grime and dirt buildup.
- Keep away from utilizing abrasive cleaners, as they will scratch the floor of the system.
- When you have any considerations about cleansing your Ring Doorbell, seek advice from the producer’s directions.
Patching the Holes
After eradicating the doorbell, you will be left with two holes in your wall: one for the wiring and one for the mounting bracket. You may patch these holes in just a few easy steps.
1. Clear the holes
Use a moist material to wipe away any grime or mud from the holes.
2. Fill the wiring gap
If the wiring gap is small, you may fill it with caulk. If the outlet is bigger, chances are you’ll want to make use of a spackling paste or a chunk of drywall.
3. Fill the mounting bracket gap
If the mounting bracket gap is small, you may fill it with caulk. If the outlet is bigger, chances are you’ll want to make use of a spackling paste or a chunk of drywall.
4. Sand the patched areas
As soon as the holes are stuffed, sand the patched areas till they’re clean.
5. Paint the patched areas
If the patched areas are seen, chances are you’ll wish to paint them to match the remainder of your wall.
6. Take away the surplus caulk
Use a moist material to wipe away any extra caulk from the patched areas.
7. Be certain that the holes are sealed correctly
Test the holes to verify they’re correctly sealed. When you can nonetheless see daylight via the holes, chances are you’ll want to use extra caulk or spackling paste. Test the holes once more to make sure that they’re sealed and weatherproof .
| Supplies | Instruments |
|---|---|
| Caulk | Screwdriver |
| Spackling paste | Utility knife |
| Drywall | Sandpaper |
| Paint | Paintbrush |
Repainting the Wall
After eradicating the Ring Doorbell, chances are you’ll discover some discoloration or harm to the wall. To revive the wall’s look, comply with these steps:
Supplies Required:
| Merchandise | Amount |
|---|---|
| Paintable caulk | 1 tube |
| Sandpaper (fine-grit) | 1 sheet |
| Primer (elective) | 1 quart |
| Paint | 1 quart (matching the unique wall coloration) |
| Paintbrush or curler | 1 every |
Steps:
- Clear the wall: Take away any remaining adhesive residue from the wall with a moist material.
- Apply paintable caulk: Fill any holes or gaps left by the doorbell mount utilizing paintable caulk. Permit the caulk to dry fully.
- Sand the floor: Utilizing fine-grit sandpaper, evenly sand the repaired space and every other discolored spots on the wall to create a clean floor.
- Apply primer (elective): If the repaired space is considerably totally different from the unique wall coloration, apply a skinny coat of primer to make sure correct paint adhesion.
- Paint the wall: Dip your brush or curler into the paint and apply a skinny, even coat to the repaired space. If obligatory, apply a second coat as soon as the primary coat has fully dried.
- Permit the paint to dry: Let the painted space dry totally earlier than touching or utilizing it.
- Test for coloration match: Evaluate the painted space to the remainder of the wall to make sure an ideal coloration match. If wanted, make minor changes with touch-up paint.
- Shield the painted space: After the paint has fully dried, think about making use of a transparent protecting coating to stop scratches or stains on the freshly painted floor.
Changing the Siding
If the Ring Doorbell is mounted on siding, it may be eliminated by rigorously following these steps:
- Flip off the facility to the doorbell on the breaker or fuse field.
- Take away the 2 screws that maintain the doorbell faceplate to the mounting bracket.
- Raise the doorbell faceplate off the mounting bracket.
- Disconnect the wires from the doorbell terminals.
- Take away the mounting bracket from the wall by unscrewing the 2 screws that maintain it in place.
- Take away the previous siding across the doorbell gap.
- Set up the brand new siding across the doorbell gap.
- Mount the mounting bracket to the wall utilizing the screws supplied.
- Join the wires to the doorbell terminals.
- Place the doorbell faceplate over the mounting bracket and safe it with the screws.
- Activate the facility to the doorbell on the breaker or fuse field.
Extra Ideas for Changing the Siding
Listed here are some further suggestions for changing the siding round your doorbell:
- Use a pointy utility knife to attain the siding across the doorbell gap earlier than chopping it out.
- Watch out to not lower into {the electrical} wires when chopping out the siding.
- Use a caulk gun to seal the sides of the brand new siding across the doorbell gap.
- Paint the brand new siding to match the remainder of your own home.
Re-Putting in the Trim Across the Ring Doorbell Space
As soon as you have eliminated the doorbell, you will have to re-install the trim across the space. This can be a comparatively easy course of, however it’s necessary to do it appropriately to make sure that the doorbell is safe and weatherproof.
Listed here are the steps on re-install the trim across the Ring Doorbell space:
1. Clear the realm across the doorbell opening with a moist material.
2. Apply a bead of caulk across the edges of the trim.
3. Press the trim into place and maintain it for just a few seconds till the caulk has set.
4. Wipe away any extra caulk with a moist material.
5. Permit the caulk to dry fully earlier than utilizing the doorbell.
Listed here are some further suggestions for re-installing the trim across the Ring Doorbell space:
Use a paintable caulk with the intention to match the colour of the trim.
When you’re having bother getting the trim to remain in place, you need to use just a few small nails to safe it.
As soon as the trim is put in, you need to use a degree to guarantee that it is degree.
Here’s a desk summarizing the steps for re-installing the trim across the Ring Doorbell space:
| Step | Description |
|---|---|
| 1 | Clear the realm across the doorbell opening with a moist material. |
| 2 | Apply a bead of caulk across the edges of the trim. |
| 3 | Press the trim into place and maintain it for just a few seconds till the caulk has set. |
| 4 | Wipe away any extra caulk with a moist material. |
| 5 | Permit the caulk to dry fully earlier than utilizing the doorbell. |
How you can Take away a Ring Doorbell
Eradicating a Ring Doorbell is a comparatively easy course of that may be accomplished in a couple of minutes. Listed here are the steps:
- Energy down your Ring Doorbell by flipping the change on the again of the system to the “off” place.
- Unscrew the 2 screws which can be situated on the backside of the Ring Doorbell.
- Fastidiously raise the Ring Doorbell off of the mounting bracket.
- Disconnect the wires from the again of the Ring Doorbell. You’ll want to word which wire is related to which terminal.
- Take away the mounting bracket from the wall.
Individuals Additionally Ask
How do I reset my Ring Doorbell?
To reset your Ring Doorbell, press and maintain the orange button on the again of the system for 15 seconds.
How do I modify the battery in my Ring Doorbell?
To alter the battery in your Ring Doorbell, take away the 2 screws which can be situated on the backside of the system. Then, raise the Ring Doorbell off of the mounting bracket and disconnect the wires from the again of the system. Lastly, substitute the previous battery with a brand new one and reassemble the system.
How do I troubleshoot my Ring Doorbell?
If you’re experiencing issues together with your Ring Doorbell, there are some things you are able to do to troubleshoot the difficulty. First, examine the facility provide to guarantee that the system is getting sufficient energy. Subsequent, examine the web connection to guarantee that the system is ready to hook up with the web. Lastly, you may attempt resetting the system by urgent and holding the orange button on the again of the system for 15 seconds.
